长春博盛量子科技有限

DioLas-Systems consist of:

• The combined high power laser driver and TEC controller of A.L.S. – a high performance driver for high power diode laser modules, optimized for the best performance in industrial applications and for the use in research and development laboratories. It delivers an output current up to 50 A and a voltage up to 3 or 6 V and is designed for cw and pulsed operation with a rise time of 100 µs. It already includes the thermo-electrical temperature controller for active temperature stabilization and regulation of the used diode laser module.

• The air forced high power laser diode heat sink of A.L.S., designed for heat loads up to 120, 80, 60 or 40 Watt (depending from the needed heat load for the used diode laser module). The heat sink includes the metal block, a temperature sensor, the Peltier cooling element (TEC) and a fan for the heat dissipation.

• The diode laser module. For most of the pigtailed modules a visible (red) pilot (aiming) diode laser can be included in the diode laser module.

• laser diode modules with output power up to 50 W for the fiber coupled ver­sions
• laser diode modules with currents up to 50 A
• microprocessor controlled
• temperature controlled
• different cases and housings possible
• fiber coupled systems with low di­ameter and low NA (0.22) fibers
  (Core diameter 100 µm, 200 µm, 400 µm, 600 µm, 800 µm, …) 
• user-friendly and reliable systems

• material processing and micro material processing,
• stabilized pump sources for diode pumped solid state lasers or fiber lasers
• sources for illumination and lightning
• research and development
• OEM versions for test systems for laser diode module parameters (lifetime, burn in)

Two different systems are available:

30 W cw/pulsed Systems (prepared for fiber coupling 400 µm, 600 µm, …)
@ 808 nm
@ 940 nm
@ 980 nm

50 W cw/pulsed Systems (prepared for fiber coupling 400 µm, 600 µm, …)
@ 808 nm
@ 940 nm
@ 980 nm

The high power laser diode system will be assembled and measured out corresponding to the special application of the customer. Of course the customer can buy also the driver and the needed laser diode heat sink and use his own diode laser module to assemble his own system.

DioLas-Systems consist of:

• The combined high power laser driver and TEC controller of A.L.S. – a high performance driver for high power diode laser modules, optimized for the best performance in industrial applications and for the use in research and development laboratories. It delivers an output current up to 50 A and a voltage up to 3 or 6 V and is designed for cw and pulsed operation with a rise time of 100 µs. It already includes the thermo-electrical temperature controller for active temperature stabilization and regulation of the used diode laser module.

• The air forced high power laser diode heat sink of A.L.S., designed for heat loads up to 120, 80, 60 or 40 Watt (depending from the needed heat load for the used diode laser module). The heat sink includes the metal block, a temperature sensor, the Peltier cooling element (TEC) and a fan for the heat dissipation.

• The diode laser module. For most of the pigtailed modules a visible (red) pilot (aiming) diode laser can be included in the diode laser module.

• laser diode modules with output power up to 50 W for the fiber coupled ver­sions
• laser diode modules with currents up to 50 A
• microprocessor controlled
• temperature controlled
• different cases and housings possible
• fiber coupled systems with low di­ameter and low NA (0.22) fibers
  (Core diameter 100 µm, 200 µm, 400 µm, 600 µm, 800 µm, …) 
• user-friendly and reliable systems

• material processing and micro material processing,
• stabilized pump sources for diode pumped solid state lasers or fiber lasers
• sources for illumination and lightning
• research and development
• OEM versions for test systems for laser diode module parameters (lifetime, burn in)

Two different systems are available:

30 W cw/pulsed Systems (prepared for fiber coupling 400 µm, 600 µm, …)
@ 808 nm
@ 940 nm
@ 980 nm

50 W cw/pulsed Systems (prepared for fiber coupling 400 µm, 600 µm, …)
@ 808 nm
@ 940 nm
@ 980 nm

The high power laser diode system will be assembled and measured out corresponding to the special application of the customer. Of course the customer can buy also the driver and the needed laser diode heat sink and use his own diode laser module to assemble his own system.